Trusted on major UK infrastructure projects
PROTEST › Maturity monitoring

Concrete maturity monitoringReal-time in-situ concrete strength

Strength you can act on, from a maturity function calibrated to the actual cement in your pour — not one generic curve stretched across all of them.

Concrete frames Post-tensioning Cold weather Thermal monitoring Precast Major civils
Accurate strengths
for formwork striking
Real-time
strength data vs cube lag
Auto-docs
every 15 min, as you build
ASTM C1074
mix-specific maturity method

From mix calibration to report — in five steps

1Calibrate mix

Input mix design and materials data. PROTEST calibrates the maturity model to your concrete.

2Install sensors

Embed temperature sensors in the concrete at critical locations before the pour.

3Record temperature

PROTEST continuously records temperature data and calculates maturity in real time.

4Analyse strength

PROTEST converts maturity to in-situ strength and benchmarks against project targets.

5Report outputs

Clear reports and alerts support decisions on formwork, load, and programme.

Proven concrete science, made practical

Temperature

Sensors cast into the pour report the concrete's temperature. PROTEST logs it every 15 minutes, continuously, building the actual thermal history as it cures.

→
Maturity

A maturity function converts that temperature-time history into an equivalent age — using a temperature-sensitivity value derived for your cement class, not a CEM I default.

→
Strength

Maturity maps to in-situ compressive strength using a calibrated curve for your specific mix — a real MPa value, on demand.

A maturity function for every cement class

Every maturity system calibrates a strength-versus-maturity curve from cubes cured at 20 °C. That part is standard practice. The second calibration is the maturity function itself — the relationship that converts a temperature history into maturity — and that is the one many systems leave on a CEM I default.

ASTM C1074 ties the accuracy of a maturity estimate to the maturity function being set for the cement actually in use, not a widely used default. On many systems, that setting is left to the user. PROTEST holds a function calibrated per cement class, so it is already done — real-time in-situ strength from the first pour.

Many systems start from a default maturity function until you add your own calibration data.

Not all maturity monitoring is equal

Maturity monitoring beating cube schedules for early-age decisions is well established. The part many systems skip is the second calibration — matching the maturity function itself to the cement going into the pour, not just the strength curve to the mix.

  Standard-cured cubes Generic maturity monitoring PROTEST
Reflects the real structure's temperature No — cured in a 20 °C water bath, not the pour Depends — only if the function's temperature sensitivity is calibrated to the mix Yes — calibrated per cement class from the first pour
Result timing Days later — lab break on a fixed schedule Real time Real time
Maturity function matched to your cement N/A Default setting — often a CEM I-based function, left unchanged Built in — per cement class, nothing to configure
Accuracy on GGBS / PFA mixes N/A — measures the cube itself Degrades — a CEM I-calibrated conversion doesn't track GGBS's different temperature sensitivity Accurate — function matches the actual cementitious combination
Role in conformity Required — conformity record (BS EN 206, BS 8500-1) Supports — early-age decisions, if properly calibrated Supports — early-age decisions, calibration already proven
Non-destructive, continuous No — one-off destructive break Yes Yes

Cube testing remains the conformity record — producer conformity under BS EN 206 and identity testing under BS 8500-1 — regardless of maturity monitoring — PROTEST supports the early-age decisions made ahead of that result, it doesn't replace it.

What the standards say about the maturity function

ASTM C1074 makes the accuracy of a maturity estimate depend on the maturity function being suited to the mixture: its temperature-sensitivity parameter has to reflect the cement actually used. A generic function is not guaranteed to be right for every mix. That is why the maturity method is really two calibrations, not one.

How a maturity estimate is madeFive steps from temperature history to estimated in-situ strength. The maturity function is set for the cement. The strength–maturity relationship is set for the mix from cube tests.Temperature historysensor readings, every 15 minutesMaturity functionset for the cement in the pourCalibration 1per cement classMaturity indexone number for the thermal historyStrength–maturity relationshipset for the mix, from cube testsCalibration 2per mixEstimated in-situ strengthreported with its assumptionsSchematic. Both calibrations are needed for the estimate to hold.
Schematic, not to scale. Both calibrations sit behind the estimate, so both need to be checked.
The strength curve

Maps maturity to MPa. Calibrated from crushed specimens cured at one temperature, usually mix by mix.

The maturity function

Converts temperature history into maturity. Usually a Nurse–Saul or Arrhenius-type function. Its temperature sensitivity should reflect the cementitious combination, but it is often left on a default.

The first gets calibrated diligently. The second is often left as it comes. The function in use is commonly Nurse–Saul or Arrhenius-based, and its datum temperature or activation energy may never have been set for the mix. ASTM C1074 gives approximate values in its appendix, and says that for maximum accuracy they should be determined for the mixture under its Annex A1.

Here's the practical effect. The strength curve is calibrated to your mix. The temperature conversion isn't — it still assumes CEM I. Lab cubes are cured at a standard 20 °C, so on a pour running close to 20 °C, that barely matters. But GGBS is significantly more temperature-sensitive than CEM I — slower-gaining in cold weather, but capable of accelerating hard in a hot mass core — and a CEM I-calibrated conversion doesn't track either direction correctly. Any site condition away from that 20 °C reference is where the mismatch grows — and those are exactly the pours where the strength data matters most.

Where the function does have a parameter, deriving the right value for a GGBS or PFA blend means the separate multi-temperature procedure in ASTM C1074 Annex A1 — mortar cubes cured in three water baths, an exercise entirely separate from the crushing schedule.

PROTEST holds maturity functions for each cement class. The strength relationship can also start from OTB's own strength predictions for your mix, refined as your team supplies calibration data while the job runs. The difference is you're verifying a live curve from the first pour, not waiting a month to build one.

Further reading in the OTB technical reference: Nurse–Saul and Arrhenius maturity functions and limitations of the maturity method.

Built for every part of the supply chain

Contractors
Strike formwork earlier, reduce propping, and keep your programme on track with real data.
Structural engineers
Verify in-situ strength, monitor thermal gradients, and assess crack risk with confidence.
Readymixers
Validate mix performance in the field and stand out from competitors with data-backed results.
Precasters
Optimise demoulding cycles using actual strength data, reducing waste and boosting throughput.
Testing labs
Replace early-age cubes with continuous, automatic data — less labour, more precision. The 28-day conformity cubes are unaffected.

Common questions on the maturity method

What engineers and contract administrators ask before adopting maturity monitoring.

Does maturity monitoring replace cube testing?

No, and any supplier who says otherwise is overselling it. The 28-day cube remains the conformity record that proves the concrete meets its specified strength class: producer conformity under BS EN 206 and identity testing under BS 8500-1. That requirement doesn't change.

What maturity monitoring replaces is the waiting. Striking, stressing and loading decisions are made days before a 28-day result exists, and they're currently made against a conservative schedule or an early cube break. Maturity gives you in-situ strength at the moment you need the decision, from the concrete in the structure rather than a cube in a tank.

What makes PROTEST different from other maturity systems?

The maturity method is really two calibrations, not one: a strength–maturity relationship for your mix, and a maturity function that converts temperature history into maturity. Most teams calibrate the first carefully. The second is often left on a default.

That default is effectively CEM I-biased. PROTEST holds a maturity function calibrated for each cement class, so the conversion matches the cementitious combination actually going into the pour — which is what ASTM C1074 relies on for an accurate estimate, and what makes the strength figure trustworthy on a GGBS or PFA mix.

Why does the cement type matter?

Because GGBS is significantly more temperature-sensitive than CEM I — slower-gaining in cold weather, but capable of accelerating hard in a hot mass core. A conversion calibrated on CEM I doesn't track either direction correctly.

Lab cubes are cured at a standard 20 °C, so on a pour sitting close to 20 °C the mismatch barely shows. It grows with every degree away from that reference — which means the error is largest on exactly the pours where the strength data matters most.

How long does calibration take before I get useful data?

The maturity function is already calibrated per cement class, so there's no multi-temperature procedure for your team to run. The strength relationship can start from OTB's own strength predictions for your mix and be refined as your calibration data comes in during the job.

The practical difference is that you're verifying a live curve from the first pour rather than waiting a month to build one before the system is useful.

Does the maturity function need calibrating for each mix?

Yes. A maturity estimate is only as good as the maturity function behind it, and that function has to be established for the cement and mix in use. A generic default curve is not a substitute. Striking and stressing decisions stay with the engineer, under the project specification.

A maturity estimate supports those decisions alongside the conformity testing that BS EN 206 and BS 8500-1 already require, and should be checked against that testing rather than used in its place. Calibration to the cement in the pour is the part to check on any system, PROTEST included.

Call you back

Leave your name and number and one of our engineers will call you back as soon as possible.

Get in touch

231 Vauxhall Bridge Road
London SW1V 1AD
protest@otbconcrete.com

Send a message